Choosing the right test leads, probes, or fixtures for your bench comes down to the instrument you are wiring up. An oscilloscope probe with switchable attenuation won't help if you need multimeter leads with alligator clips, and a 100MHz probe pair won't necessarily cover a 200MHz scope. The four new kits here span both roles, from a $9.95 multimeter lead set to a $29.99 four-probe oscilloscope pack.
Quick Take
In this group of four new probe and lead kits, oscilloscope probes are the main story. Two kits are based on the JINHAO P6100 series: a two-probe set at $17.99 and a four-probe set at $29.99. A third scope option is the Peakelect 200MHz two-pack at $19.99 with a 1X/10X sliding switch and accessory kit. The fourth item is a $9.95 multimeter lead set with alligator clips, rated at 1000V/20A and universal to all digital multimeters.
Listed-Price Comparison
| Product | Listed Price | Price Bar |
|---|---|---|
| Peakelect 2-Pack Oscilloscope Clip Probes 200MHz | USD 19.99 | |
| 4 Four New 100MHz Oscilloscope Clip Probes for HP Tektronix Hitachi, US Seller | USD 29.99 | |
| Multimeter Test Leads for Fluke Meter Electrical Alligator Clip Probes 1000V 20A | USD 9.95 | |
| 2x 100MHz Oscilloscope Scope Analyzer Clip Probe Test Leads Kit for HP Tektronix | USD 17.99 |
The listed prices run from $9.95 to $29.99. The multimeter lead set is the lowest-priced item, while the four-probe 100MHz oscilloscope set sits at the top of the range. The two-pack 100MHz kit and the Peakelect 200MHz pair sit close together in the middle.
Decision Matrix
| Scenario | Recommended Choice |
|---|---|
| You need two oscilloscope probes and want a 200MHz design | Peakelect 2-Pack Oscilloscope Clip Probes |
| You need four 100MHz oscilloscope probes for HP/Tektronix/Hitachi | 4 Four New 100MHz Oscilloscope Clip Probes |
| You need multimeter leads with alligator clips for Fluke Meter work | Multimeter Test Leads for Fluke Meter Electrical Alligator Clip Probes |
| You need two 100MHz oscilloscope probes and want a P6100 series kit | 2x 100MHz Oscilloscope Scope Analyzer Clip Probe Test Leads Kit |
Product Notes
Peakelect 2-Pack Oscilloscope Clip Probes 200MHz with Accessory Kit 1X 10X
This is the only 200MHz option in the lineup. Each probe uses a 1X/10X sliding switch, and the set arrives with an accessory kit and a grounding crocodile clip. Choose it when your measurements need the higher bandwidth or when you want the attenuator switch built into each probe. The limitation is the probe count: with just two probes, four-channel work would require a second set. It is a focused choice for a two-channel scope bench rather than a full four-channel solution.
4 Four New 100MHz Oscilloscope Clip Probes for HP Tektronix Hitachi, US Seller
This is the only four-probe oscilloscope set in the comparison. The P6100-series probes are rated at 100MHz and include switchable attenuation, 10MΩ input resistance in 10X mode, and 120cm cables; the country of origin is China. Choose it when all four oscilloscope channels need a probe in one purchase. The limitation is the listed price, which is the highest in the group. If two channels are all you need, a smaller kit will take up less bench space and cost less, but this set handles a four-channel front end directly.
Multimeter Test Leads for Fluke Meter Electrical Alligator Clip Probes 1000V 20A
This is the multimeter-focused product in the roundup, with alligator clips on the test end and a 1000V/20A rating. It is universal to all digital multimeters, uses silicone insulation, and has sharp probes suited to IC pins, LEDs, and small components. Choose it for Fluke Meter electrical work when you are replacing meter leads rather than adding oscilloscope probes. The limitation is that it occupies a different bench role than the three scope kits, so it is aimed at multimeter connections rather than scope traces.
2x 100MHz Oscilloscope Scope Analyzer Clip Probe Test Leads Kit for HP Tektronix
This pair uses the same P6100 series and the same attenuator behavior as the four-probe set, with 120cm cables, mini alligator clips, a ground lead, and a screwdriver for adjustments. Choose it for a two-channel oscilloscope under the HP, Tektronix, or Hitachi naming from the title. The limitation is the probe count: two probes means two channels, so a four-channel measurement would require another kit.
Final Recommendation by Use Case
- Four-channel oscilloscope bench: start with the 4 Four New Oscilloscope Clip Probes; the single kit covers all four inputs.
- Two-channel oscilloscope with higher bandwidth: choose the Peakelect 2-Pack Oscilloscope Clip Probes for its higher bandwidth and included accessory kit.
- Two-channel oscilloscope with a standard probe kit: the 2x Oscilloscope Scope Analyzer Clip Probe Test Leads Kit is the smaller version of the same series.
- Multimeter-only bench work: the Multimeter Test Leads with alligator clips covers digital multimeter use.
